Important Plumbing Tips for Installing a Bathtub
Important Plumbing Tips for Installing a Bathtub
Blog Article
We have come across this post on Installing A Bathtub listed below on the net and figured it made sense to relate it with you on this site.
Setting up a bathtub isn't specifically brain surgery, yet it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a new one is also a moderately tough job. If the old tub is readily available, the project can move immediately; if you need to open up a wall to eliminate the old tub as well as position the new bathtub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will certainly need a helper to move out the old bathtub and set in the brand-new one. See to it you have qualified yourself for the task and fit trying it. As opposed to employing a service provider to take over a halfway-completed job, it is far better to take into consideration using one before you start. Opportunities are you might need a specialist plumber to make tube connections.
This post will certainly help you install a new bath tub in your washroom if you have already bought a new bathtub and do not need to change the setup of your previous supply of water pipes.
Your devices as well as product checklist must comprise the following:
Getting ready for the Installment
Firstly, the supporting structure supplied with the bath must be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be fitted in its final placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, turn on the faucets to drain any water staying in the system. The process of getting rid of the existing faucets can be quite problematic due to the limited accessibility that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipelines have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, position the bathtub in the needed placement. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the tub until the level checks out degree.
To mount taps, fit the bottom of the furthest versatile faucet connector to the appropriate supply pipe by making a compression join; after that do the same for the various other faucet.
Switch on the water supply and check all joints and new pipework for leaks as well as tighten them if needed. Load the bathtub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and securing around the bath tub must wait up until the tub has been made use of a minimum of when as this will certainly settle it into its final placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in area between the tap as well as the sink. Protect the faucet in position with the producer offered backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type must be linked to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to split a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, bring about difficulties with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and also fittings. They are sold in tubes and cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub is in use. The sealer can break fairly early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the market. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our topic on How to Install a Bathtub Yourself. Thanks for taking the time to browse our short article. Sharing is good. Helping people is fun. Many thanks for your time. Kindly visit our blog back soon.
This Resource Report this page